-
The three options I priced out — and two I excluded
-
Dimension 1: Accuracy and part size
-
Dimension 2: The price tag vs. the invoice
-
Dimension 3: Response time and utilization
-
Dimension 4: The calibration economics nobody quotes
-
When the $200 tool is the correct answer
-
What I'd choose in each scenario
The three options I priced out — and two I excluded
Every time someone asks me to "look at a FARO," the real question is narrower than it sounds. They're usually deciding between three things: a portable CMM arm, a laser tracker, or sending parts out to a metrology lab. Those are the three I compared for our 2025 capital budget.
I excluded two categories on purpose. Lab analytical instruments — HPLC systems, double-stranded RNA workflows, that whole category — sit in a different procurement line with a different budget owner. Same for electrical reference gear. If you're calibrating electronics, a bench multimeter like the Fluke 8508A is the correct instrument, and no portable CMM will substitute for it. Neither will FARO sell you one. That's fine. Knowing what a vendor doesn't do is part of evaluating what they do.
So: arm vs tracker vs outsourcing. Four dimensions. I'll give you the comparison first, then the scenarios where each one wins.
Dimension 1: Accuracy and part size
A FARO Quantum or ScanArm in the mid-range lands around 0.02–0.05 mm volumetric accuracy, depending on reach and whether you're using a scanner. That's plenty for most machined parts, fixtures, and first-article inspection up to a couple of meters.
A laser tracker is a different animal. The Vantage series holds similar accuracy but over 10–30 meters, which is why it shows up in aerospace assembly and shipyard work. If your parts fit on a bench, a tracker is overkill. If your parts are the bench, an arm is useless.
Outsourcing gives you whatever the lab owns — often a stationary CMM with better volumetric accuracy than either portable option. But you pay for it in turnaround, not just dollars.
Here's the part that surprised me: the accuracy spec is rarely the deciding factor. Temperature and fixturing move the number more than the machine class does. We measured the same aluminum bracket on an arm in our 24°C shop and in a lab at 20°C. The difference was 0.018 mm — bigger than the gap between the arm and tracker spec sheets. Nobody puts that in the brochure.
Dimension 2: The price tag vs. the invoice
Ballpark, based on three quotes we collected in Q1 2025 — verify with your own quote, because configuration changes everything:
- Portable CMM arm (FARO Quantum-class, mid-reach): roughly $40,000–$120,000
- Laser tracker (Vantage-class): roughly $100,000–$200,000+
- Outsourced inspection: $150–$400 per hour, or $500–$2,000 per project
The sticker price is the easy part. I built a TCO sheet for our last capital request and the purchase price was 58% of the five-year cost. The rest:
- Annual calibration and certification: $3,000–$8,000 for an arm, more for a tracker
- Software seats and maintenance: $5,000–$15,000 up front, plus renewal
- Training: two people, a week each, plus the productivity you lose while they're learning
- Fixtures and stands: easy to forget, hard to avoid
I learned this the expensive way in 2022. We bought a used arm at a 30% discount and skipped the extended calibration package to save about $6,000. Six months later the encoder drifted, we shipped it back, and the repair plus expedited recalibration came to $9,400. Net loss on that "saving": roughly $3,400, plus three weeks without the tool. The cheap option wasn't cheaper. It was just cheaper up front.
Dimension 3: Response time and utilization
This is where outsourcing quietly wins for a lot of shops. A lab with a two-day turnaround beats an arm that sits idle because nobody's trained on it.
I assumed "portable" meant "use it anywhere, anytime." Didn't verify. Turned out our arm needs a stable surface, a warm-up period, and an operator who actually understands alignment. The first month, utilization was about 12 hours. We'd paid $70,000 for something that got used twice a week.
Utilization is the number that kills the business case, and it's the one vendors never ask about. Ask yourself honestly: how many hours per month will this thing actually run? Under 40 hours, the math usually favors outsourcing. Above 100, ownership starts to make sense. Between 40 and 100, it's up in the air and depends on how much you value same-day answers.
Dimension 4: The calibration economics nobody quotes
Over five years, calibration runs 8–12% of the original purchase price for an arm and closer to 15% for a tracker. Not a deal-breaker, but it's a line item that changes the comparison.
Honestly, I'm not sure why calibration pricing varies so much between service providers — same standard, same scope, quotes that differ by 40%. My best guess is it's a mix of travel logistics and how much buffer each provider builds into their schedule. If someone has a better explanation, I'd genuinely like to hear it.
Acceptance testing for coordinate measuring systems follows ISO 10360 for CMMs and ASME B89.4.22 for articulated arm coordinate measuring machines. Ask any vendor which tests they'll run and whether the results are included in the quote. "It's calibrated" without a test report is a red flag.
When the $200 tool is the correct answer
Not every measurement problem needs a metrology purchase. If you're checking whether a frame is square, a Starrett angle finder or a good machinist's square will do it for under $200 and never needs calibration. I've watched companies buy a $60,000 arm to solve a problem a $150 tool would have handled.
I'd rather work with a vendor who says "for that application, you don't need us" than one who sells a CMM to everyone who calls. The specialist who knows their boundary is more credible on everything inside it. That's not charity — it's how you build a relationship that survives the second purchase.
What I'd choose in each scenario
Choose outsourcing if: you need fewer than 40 measurement hours a month, your parts vary wildly, or you need certified results with a paper trail and no capital outlay.
Choose a portable CMM arm if: you inspect parts up to a couple of meters, you need same-day answers on the floor, and you can commit to training two operators and running it 100+ hours a month.
Choose a laser tracker if: your assemblies are measured in meters, not millimeters of bench space, and the cost of a misaligned large structure dwarfs the equipment price.
Bottom line: the FARO CMM machine price is a starting point, not the decision. The decision is utilization, calibration, and whether the measurement problem is actually yours to own. Run the five-year number before you run the purchase order.